Ht-instruments HT4016 Manual de usuario

©Copyright HT ITALIA 2007 Release EN 1.06 - 26/10/2007 ENGLISH User’s manual

HT4014-HT4016 EN - 94.2. FUNCTION KEY DESCRIPTION 4.2.1. R-H / key: range selection / backlight function (HT4016 only) For R-H function: 1. P

HT4014-HT4016 EN - 104.3. DESCRIPTION OF ROTARY SWITCH FUNCTION 4.3.1. AC Voltage measurement WARNING Maximum input for AC Voltage measure

HT4014-HT4016 EN - 114.3.2. DC Voltage measurement WARNING Maximum input for DC Voltage measurements is 600V. Do not attempt to take any vo

HT4014-HT4016 EN - 124.3.3. AC Current measurement WARNING • Make sure that all the test leads are disconnected from the meter's ter

HT4014-HT4016 EN - 134.3.4. DC Current measurement (HT4016 only) WARNING • Make sure that all the test leads are disconnected from the me

HT4014-HT4016 EN - 144.3.5. Resistance measurement WARNING Before taking any in circuit resistance measurement, remove power from the circu

HT4014-HT4016 EN - 154.3.6. Continuity Test WARNING Before taking any in circuit resistance measurement, remove power from the circuit bein

HT4014-HT4016 EN - 164.3.7. Diode test (HT4014 only) WARNING Before taking any in circuit resistance measurement, remove power from the ci

HT4014-HT4016 EN - 174.3.8. Frequency measurement (HT4014 only) WARNING Maximum input voltage of AC VOLT Range is 600Vrms. Do not attempt

HT4014-HT4016 EN - 185. MAINTENANCE 5.1. GENERAL INFORMATION 1. This digital clamp meter is a precision instrument. Whether in use or in storag

HT4014-HT4016 EN - 1CONTENTS: 1. SAFETY PRECAUTIONS AND PROCEDURES...2 1.1. Prelimin

HT4014-HT4016 EN - 196. TECHNICAL SPECIFICATIONS 6.1. CHARACTERISTICS Accuracy is indicated as [% of reading + digit number]. It is referred to

HT4014-HT4016 EN - 20Diode test (HT4014 only) Range Resolution Max. Open Loop voltage Overload protection 1mV about 3.3VDC 600V rms Frequen

HT4014-HT4016 EN - 216.2.2. EMC This apparatus was designed in accordance with EMC standards in force and its compatibility has been tested in a

HT4014-HT4016 EN - 227. SERVICE 7.1. WARRANTY CONDITIONS This equipment is guaranteed against any material fault or manufacturer’s defect, in ac

HT4014-HT4016 EN - 21. SAFETY PRECAUTIONS AND PROCEDURES This instrument is conforms to safety standard EN 61010, relating to electronic measuri

HT4014-HT4016 EN - 31.1. PRELIMINARY • This apparatus has been designed for use in an environment of pollution degree 2. • It can be used for

HT4014-HT4016 EN - 41.4. DEFINITION OF MEASURING (OVERVOLTAGE) CATEGORY The norm EN 61010: Safety requirements for electrical equipment for mea

HT4014-HT4016 EN - 52. GENERAL DESCRIPTION This manual is referred to two models: HT4014 and HT4016; the difference between the models is fundam

HT4014-HT4016 EN - 63. PREPARATION FOR USE 3.1. INITIAL This instrument has been checked mechanically and electrically before shipment. All prec

HT4014-HT4016 EN - 74. OPERATING INSTRUCTIONS 4.1. INSTRUMENT DESCRIPTION 4.1.1. Commands description HT 40 18 LEGEND: 1. Inductive clamp ja

HT4014-HT4016 EN - 84.1.3. Use of rubber test leads holster In standard accessories of instrument there is a rubber holster that, inserted on c