Ht-instruments FULLTEST3 Manual de usuario Pagina 39
- Pagina / 92
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
FULLTEST 3
EN - 38
Figure 26: Connection of test leads to tested wiring for LOOPL/PE measurement
7) READY message will appear when mains voltage UL/N (LOOP L/N) or UL/PE (LOOP L/PE) within
100 265 V or UL/L (LOOP L/L) within 100 460 V is present. Carry out the measurement by
pressing the START button.
8) Test result (loop impedance) will be displayed in green colour equipped with green symbol and
with beep-beep sound if measured/calculated ISC corresponds to entered limit mode and other
entered parameters. If measured/calculated ISC does not correspond to entered limit mode and
other entered parameters the result will be displayed in red colour equipped with red symbol
and with longer beep sound. See the display outlook with test result on the figure 22.
9) Save the test result by pressing the SAVE hard button twice, for further instructions see the
“MEMORIZING EXAMPLE” section.
10) Press the EXIT hard key to clear displayed result, actual input voltage UL/L or UL/N or UL/PE will
start to be displayed again.
CAUTION
In case voltage UL/N (LOOP L/N measurement) or voltage UL/PE (LOOP L/PE
measurement) within required range 100 265 V is present at L/N/PE test
terminals (also displayed) but there is no READY message displayed, check if
energizing socket is correctly earthed!
In case voltage U
L/L (LOOP L/L measurement) within required range 100 460
V is present at L/N test terminals (also displayed) but there is no READY
message displayed, check if energizing socket is correctly earthed!
If limit mode STD is selected (result is not evaluated), then the result will be
displayed in white colour.
The following specific information can be shown on the display during the measurement:
Information displayed Description
VOLTAGE OUT OF RANGE
Input voltage UL/N or UL/PE out of required range 100
265 V (L/N or L/PE measurement) or out of required range
173 460 V (L/L measurement) after pressing the START
key.
FUSE F3!
Fuse F3 is blown.
HOT!
Internal load is overheated.
Wait to cool it down!
MEASUREMENT FAILED!
Input voltage failed during the measurement (disconnection
of test leads, installation fuse tripped etc.)
- FULLTEST 1
- FULLTEST 3 2
- Table of contents: 2
- 2. GENERAL DESCRIPTION 7
- 3. PREPARATION FOR USE 10
- 4. OPERATING INSTRUCTIONS 11
- PE-2WIRE function 13
- 5. MEASUREMENTS 14
- Short unisolated wire 15
- Red test leads 2,5 mm 15
- PE-2WIRE MEASUREMENT 17
- NOM (5) 17
- PE-4WIRE DISPLAY EXPLANATION 19
- PE-4WIRE test result 19
- PE-4WIRE MEASUREMENT 21
- PE 0 20 21
- ISO DISPLAY EXPLANATION 23
- ISO test result 23
- ISO MEASUREMENT 24
- APP or IREAL 27
- APP 0 200 mA 28
- REAL 0 200 mA 28
- TES NOM 28
- 29
- L/N and UL/PE will start to 33
- IN/2 IN 2IN (4) 5IN 33
- SC LIM, which is the bases 35
- SC MIN must 36
- L/N or LOOPL/PE measurement 38
- L/N measurement 38
- L/L measurement 38
- L/PE will start to be 42
- IN and actual trigger 47
- RES PLUG measurement 47
- IN within required range 47
- APP 0 5.06 kVA 50
- L/N 195 253 V 50
- L 0 20 A 50
- PE 0.25 mA 10 A 50
- L1/2 360 460 V 53
- L2/3 360 460 V 53
- L3/1 360 460 V 53
- CLAMP DISPLAY EXPLANATION 54
- CLAMP test result 54
- CLAMP measurement 55
- LEAK measurement, CLAMP mode 58
- L/N 195 253 V 59
- PE CURRENT OVERRANGE! 60
- L CURRENT OVERRANGE! 60
- MEMORY LANGUAGE SETUP 61
- OPERATOR TESTER INFO 61
- USBCLEARMEM INFO 61
- LAST RESULT 62
- LANGUAGE 63
- TESTER INFO 63
- DATE/TIME NOMINAL VOL 64
- LEVEL NAMES 64
- SAFET INPUT RESETCONTACT VOL 64
- 50 V25 V 65
- CONTACT VOL 65
- EN - 65 66
- EN - 66 67
- EN - 67 68
- EN - 68 69
- 230 V 240 V 70
- NOMINAL VOL 70
- DISABLED ENABLED 70
- SAFETY INPUT 70
- 7. MEMORY FEATURES 72
- 8. MEMORIZING EXAMPLE 73
- 9. RECALL RESULTS 75
- EN - 75 76
- 13. MAINTENANCE 77
- A or RCD function 78
- PE measurement 79
- PE-4WIRE, 25A) 80
- PE-2WIRE, 0.2A)) 80
- N CAT III 300 V 82
- L/PE): 450 k 85
- C at IN: 85
- TRIG): 0 460 VAC 86
- RES): 100 M 86
- TRIG): 450 k 86
- APP and PACT CAT II 300 V 87
- PE (POWER) 87
- L1/2, UL2/3, UL3/1 88
- CLAMP) 88
- 15. SERVICE 91
Relacionado con productos y manuales para Herramientas Ht-instruments FULLTEST3
(4 paginas)
Herramientas Ht-instruments HT14N Manual de usuario
(12 paginas)
(12 paginas)
Herramientas Ht-instruments HT154 Manual de usuario
(13 paginas)
(13 paginas)
Herramientas Ht-instruments GEO416 Manual de usuario
(116 paginas)
(116 paginas)
Herramientas Ht-instruments HT21 Manual de usuario
(17 paginas)
(17 paginas)
Herramientas Ht-instruments HT7051 Manual de usuario
(35 paginas)
(35 paginas)
Herramientas Ht-instruments HT157 Manual de usuario
(68 paginas)
(68 paginas)
Herramientas Ht-instruments HT210 Manual de usuario
(19 paginas)
(19 paginas)
Herramientas Ht-instruments HT307 Manual de usuario
(11 paginas)
(11 paginas)
Herramientas Ht-instruments HT309 Manual de usuario
(13 paginas)
(13 paginas)
Herramientas Ht-instruments HT322 Manual de usuario
(16 paginas)
(16 paginas)
Herramientas Ht-instruments HT32 Manual de usuario
(23 paginas)
(23 paginas)
Herramientas Ht-instruments HT326 Manual de usuario
(21 paginas)
(21 paginas)
Herramientas Ht-instruments HT327 Manual de usuario
(21 paginas)
(21 paginas)
Herramientas Ht-instruments HT3310 Manual de usuario
(16 paginas)
(16 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales